Hidden Remote Vacuum Brake Booster



Hidden Remote Vacuum Brake Booster

Postby 2Loose » September 12th, 2012, 3:47 pm

I've been using a remote, hidden, vacuum brake booster on my two Chevy trucks, a '55 and a '58, for 10 to 12 years now with no problems...

I recently started doing a fair amount of work on my '55 halfton 4x4, to convert it to a cross steer setup, and rebuild the Olds 455 motor, which had developed a rod knock. Went through the brake system, rebuild kits in the front calipers and rear drums, and the master cylinder and slave vacuum master cylinder. They are back in the truck, the system got bled yesterday, and I have good solid pedal feel.

Here's a schematic of how this system looks:
Image

Here's a top view of the remote slave vacuum master cylinder, visible is the large vacuum port, the bleeder screw, the outlet connection (facing up) to the brakes on the end, and the inlet connection on the side that comes from the actuating master cylinder....

With the outlet on top like this I have not had any problems getting this master cylinder to self bleed all the air out when filling the system. The actuating master cylinder should be bench bled before installing to make sure all the air is out of it....
Image

I bleed this system by slowly pumping the brake pedal, keeping the master cylinder filled, with the bleeder screw at one wheel at a time cracked and a tube on the bleeder with one end submerged in a container with brake fluid. I don't use a vacuum bleeder with this setup. It helps if two people can do this, but I did it by myself yesterday with no problems. With my 4x4 truck, even though the two master cylinders are under the floor, they are still above the brakes, so it will self bleed pretty well by itself, I just choose to help it along....

Another view.....
Image

On one side is a filter system for the ambient air that goes in/out on the non-vacuum side of the diaphragm....
Image

Here's the stock under floor master cylinder for the '55 Chevy half-ton pickup, and the slaved remote vacuum booster master cylinder...
Image

It's been difficult to get a good shot of the actual installation. If I get one I will post it.

Here's what the fire wall looks like on this truck, I like to keep 'em clean!
Image

Aloha,
Willy
Slow Old Man = Fast Old Cars
My Do It Yourself Web Page...
2Loose

User avatar
 
Posts: 475
Joined: December 29th, 2008, 1:59 pm
Location: Maui

Re: Hidden Remote Vacuum Brake Booster

Postby Indycars » September 13th, 2012, 8:11 am


Is there any limitation as to how far you can mount the remote booster from the
main master cylinder?

Love that engine compartment! That was an understatement when you said
you like them clean! :)

Rick
Too much is just enough!!!

- Check Out My Dart SHP Engine Project: viewtopic.php?f=69&t=3814
- Need a Dynamic Compression Ratio Calculator: viewtopic.php?f=99&t=4458
Indycars

User avatar
Forum Admin
Forum Admin
 
Posts: 4424
Joined: May 25th, 2010, 8:58 am
Location: Yukon, OK

Re: Hidden Remote Vacuum Brake Booster

Postby grumpyvette » September 13th, 2012, 8:14 am

IF YOU CAN,T SMOKE THE TIRES AT WILL,FROM A 60 MPH ROLLING START YOUR ENGINE NEEDS MORE WORK!!"!
IF YOU CAN , YOU NEED BETTER TIRES AND YOUR SUSPENSION NEEDS MORE WORK!!
grumpyvette

User avatar
Site Admin
Site Admin
 
Posts: 14105
Joined: September 14th, 2008, 1:40 pm
Location: florida

Re: Hidden Remote Vacuum Brake Booster

Postby 2Loose » September 13th, 2012, 12:30 pm

As far as I know there is no limitation on how far the slave vacuum master is from the original master cylinder. The brake fluid is incompressible and as we use steel brake lines, it should not make any difference if the connecting link is 6" or 60" long. I recently acquired an under floor electric boost system, using an accumulator, I'll be playing with that and will post when I get some experience with it. I'm thinking of putting it under the floor of my '55 Chevy Sport Coupe (hardtop)....
Willy
2Loose

User avatar
 
Posts: 475
Joined: December 29th, 2008, 1:59 pm
Location: Maui


Return to Suspension and Brakes: Repairs and Modifications

Who is online

Users browsing this forum: No registered users and 1 guest

cron