detonation/pre-ignition



detonation/pre-ignition

Postby grumpyvette » September 22nd, 2008, 10:38 am

Detonation vs power
this is worth reading,
viewtopic.php?f=50&t=9816

http://www.enginebasics.com/Advanced%20 ... ooler.html

http://kb-silvolite.com/article.php?action=read&A_id=58

if you do a simple compression test and find out a single or pair of cylinders read far less than most of the others theres an excellent chance your dealing with a defective head gasket, detonation damage on the pistons and rings, a broken valve spring that won,t keep the valve seated, or a busted valve or piston and be aware if it over heated a top compression ring that ring might have expanded enough for the piston ring ends to butt, expand and lock the ring in the bore for an instant, resulting in cracking or deforming the piston groove, if it did the compression ring seal will have been mostly destroyed(PERMANENTLY)
might also check the cam/lifters/pushrods. if valve(s) are stuck open, cracked cylinder head,no compression.
Image

Image

Image
Image
Image

TYPICAL DAMAGE APPEARANCE

A hole has formed in the piston crown after a relatively short running time.
The upper third of the hole has formed by melting, the remaining two thirds, where the hole opens out in the downward direction, by breakage.
The piston skirt and undamaged part of the piston head often show no sign of thermal overload, and the hardness relaxation is within normal limits. In many cases scuffing has not even occurred.

ASSESSMENT

Holes in the piston crown form mostly in high compression engines with predominantly hemispherical combustion chambers. Specific combustion defects cause such rapid local overheating that material in the affected area becomes pasty. The inertia forces due to the axial piston movement and the fast flowing combustion gases cause removal of the soft material. As a result of the loss of strength in this area, the combustion pressure then causes mechanical failure of the remaining two-thirds of the piston crown thickness. This lower part of the hole opens out downwards. Such a rapid local overheating of the piston crown to a pasty condition can only be caused by pre-ignition. Combustion is initiated some time prior to the actual spark enabling the flame to operate on the piston crown much longer than usual. Tests have shown that the piston crown heats up locally to the melting point within a few seconds under continuous pre-ignition.

With pre-ignition, combustion is initiated by a glowing area in the combustion chamber when the mixture self-ignition temperature is exceeded. Probable sources are the sparking plug, the exhaust valve and deposits adhering to the combustion chamber walls.

POSSIBLE CAUSES

The fuel quality must match the compression ratio of the engine, i.e. the octane rating of the fuel must cover the engine octane requirement at all operating conditions
Diesel fuel in petrol.
Oil in combustion chamber due to leakage past piston rings or valve guides.
Sparking plugs with incorrect heat range.
The ignition timing and advance/retard characteristics and the distributor condition.
Leaking exhaust valves.
Combustion chamber deposits (hard and soft carbon).
Inlet temperature too high. This can be considerably raised by a faulty or incorrect exhaust, particularly with uniflow scavanged cylinder heads.
High engine or inlet temperature due to inadequate under-bonnet ventilation.
General overheating.
engine heat can be a huge issue, detonation can destroy even a well built engine, I have tried to maintain an 8:1-8.4:1 dynamic compression ratio and a .040-.042 quench in most of my engines,I try to keep the oil temps at no more than 220F most of the time and ideally under 215F, I try to keep coolant temps under 190F most of the time and try to avoid getting coolant over 215 f, keep in mind that you can,t audibly hear detonation in most engines in the upper rpm range until it becomes rather extreme and potentially rather destructive, and that just because you can,t hear it at lower rpms or when its not happening consistently, its not an indication that the cumulative damage is not occurring over time.
I lost count of the guys I know who built engines that "for no apparent reason... busted pistons or rings" when those engines get torn down and closely inspected DETONATION is frequently a prime suspect, and todays crappy fuel octane is a prime contributor.
every combos different and simple things like polishing combustion chambers. retarding a cam a few degrees,using a larger more efficient radiator, and changing the fuel/air ratio and ignition advance curve or adding a highly effective scavenging header on a low restriction exhaust can make or brake a combo as far as its tendency to get into detonation.
Image
Image
Image
Image

and be aware if the engine over heated a top compression ring, that ring might have expanded enough for the piston ring ends to butt, expand and lock the ring in the bore for an instant, resulting in cracking or deforming the piston groove, if it did the compression ring seal will have been mostly destroyed(PERMANENTLY)

viewtopic.php?f=52&t=2630&p=13142&hilit=curtain#p13142

viewtopic.php?f=55&t=613&p=1379&hilit=octane+booster#p1379

viewtopic.php?f=52&t=4081&p=10861&hilit=curtain#p10861

viewtopic.php?f=53&t=510

viewtopic.php?f=55&t=2718&p=12119&hilit=calculate+octane#p12119

some of the major factors in your engines potential power, is the volumetric efficiency (how efficiently you fill and empty the cylinders) and the octane of the fuel used, compression ratio and detonation limits,
With detonation, prevention the main factors are
Ignition timing
Quench
FUEL OCTANE
DCR
and cylinder heat level
you’ll be fairly safe if you stay under
8.5:1 dcr at 170f degrees
8.25 dcr at 180f degrees
7.8:1 dcr at 210f degrees
and keep the quench in the .036-.043 range
heres some differant calculators
http://www.kb-silvolite.com/calc.php?action=comp2 http://www.wallaceracing.com/dynamic-cr.php
http://www.smokemup.com/auto_math/compression_ratio.php http://not2fast.wryday.com/turbo/compre ... sure.shtml
average the results

the numbers are for 92 octane premium gas run at a 14.7:1 a/f ratio

BTW heres a VERY SIMILAR GRAPH

Image
[
Image
Image

Image
Image
failure to verify clearances, verify valve train geometry , provide lubrication, and maintain cooling , stay out of DETONATION,or use of inferior components or exceeding your engines valve train control limitations, or red line on rotating assembly design strength can get darn expensive
and can result in expensive lessons in engine repair

http://www.misterfixit.com/deton.htm]http://www.misterfixit.com/deton.htm

I won,t get into the extensive details of why, but heres what you can DO,

(1) retard the cam 4 degrees, (this tends to reduce your dcr and lower cylinder temps due to slightly lower DCR)

(2) add a pusher fan or in some way REDUCE your coolant temp, this tends to reduce the detonation tendency

(3) richen the air/fuel ratio to about 12.7:1 this tend to increase power and reduce the potential for detonation due to cooler cylinder temps)

(4)change to a spark plug two ranges colder and change the plug gap to .040, this tends (at least in theory)to reduce the plugs tip temp due to a lower electrical resistance of the spark jumping the gap)

(5) add some fresh coolant,and flush the radiator and install a 160 degree t-stat, some water wetter or purple ice ,in that coolant might help

(6) add a good multi spark ignition and have your distributor curve checked/modified to advance smoothly from 1000rpm to full advance at 3000rpm

(7) check for and remove any vacuum leaks

(8)next time the heads are off POLISH the combustion chambers, remove any sharp edges and make sure the QUENCH falls in the .037-.043 range

(9)swapping too aluminum heads is a good way to reduce the detonation tendency in some engines

(10) swapping to a larger capacity and more efficient,aluminim radiator helps in some cases

richen up the mix to 12.5:1 for max power/tq vs low emmissions and you can cheat slightly as the cylinder temps go down slightly.
keep in mind ALUMINUM absorbs and allows the transfer of heat to the coolant at a much faster rate, so your less likely to have cylinder temps raise into the detonation range as quickly.
and it should be obvious that your igntion curve and spark strength will also effect results, personally Ive found the BETTER MSD multi strike ignitions keep the cylinders cleaner and less likely to detonate

A bore scope can help locate problems like leaking intake gaskets, do a google search on (SLIPV618)its a bore scope I use and it easily slides thru a spark plug hole
http://store.dejavujewelry.com/tlw-slipv618.html

just be aware that oil in the runners doesn,t necessarily indicate a bad intake gasket because reversion pulse at low rpms can and does suck oil out of the cylinders into the intake runners even on engines with perfectly sealed intake gaskets if the ring seal or valve guides are warn
IF YOU CAN,T SMOKE THE TIRES AT WILL,FROM A 60 MPH ROLLING START YOUR ENGINE NEEDS MORE WORK!!"!
IF YOU CAN , YOU NEED BETTER TIRES AND YOUR SUSPENSION NEEDS MORE WORK!!
grumpyvette

User avatar
Site Admin
Site Admin
 
Posts: 14105
Joined: September 14th, 2008, 1:40 pm
Location: florida

Re: detonation/pre-ignition

Postby grumpyvette » October 7th, 2008, 12:48 pm

READ THIS LINK
http://zhome.com/ZCMnL/PICS/detonation/detonation.html

http://www.streetrodstuff.com/Articles/Engine/Detonation/

http://www.misterfixit.com/deton.htm

http://www.turbofast.com.au/racefuel10.html

viewtopic.php?f=55&t=613&p=817&hilit=octane+booster#p817

http://www.kitcarmag.com/techarticles/eliminating_detonation_pre_ignition/index.html

viewtopic.php?f=54&t=8463&p=29691&hilit=piston+squirters#p29691

Taken from http://www.misterfixit.com/

WHAT IS DETONATION?
Detonation (also called "spark knock") is an erratic form of combustion that can cause head gasket failure as well as other engine damage. When a head gasket thickness is listed its supposed to be the compressed gasket thickness ,this can be important in determining quench distance.
Detonation occurs when excessive heat and pressure in the combustion chamber cause the air/fuel mixture to auto ignite. This produces multiple flame fronts within the combustion chamber instead of a single flame kernel. When these multiple flames collide, they do so with explosive force that produces a sudden rise in cylinder pressure accompanied by a sharp metallic pinging or knocking noise. The hammer-like shock waves created by detonation subject the head gasket, piston, rings, spark plug and rod bearings to severe overloading.
Mild or occasional detonation can occur in almost any engine and usually causes no harm. But prolonged or heavy detonation can be very damaging. So if you hear knocking or pinging when accelerating or lugging your engine, you probably have a detonation problem.

A DOZEN WAYS TO PREVENT DETONATION
1. Try a higher octane fuel. The octane rating of a given grade of gasoline is a measure of its detonation resistance. The higher the octane number, the better able the fuel is to resist detonation. Most engines in good condition will run fine on regular grade 87 octane fuel. But engines with high compression ratios (over 9:1), turbochargers, superchargers, or with accumulated carbon deposits in the combustion chamber may require 89 or higher octane fuel.
How a vehicle is used can also affect its octane requirements. If a vehicle is used for towing or some other application where the engine is forced to work hard under load, a higher octane fuel may be necessary to prevent detonation.
If switching to a higher octane fuel fails to eliminate a persistent detonation problem, it probably means something else is amiss. Anything that increases normal combustion temperatures or pressures, leans out the air/fuel mixture, or causes the engine to run hotter than normal can cause detonation.
2. Check for loss of EGR. The Exhaust Gas Recirculation (EGR) system is one of the engine's primary emission controls. Its purpose is to reduce oxides of nitrogen (NOX) pollution in the exhaust. It does this by "leaking" (recirculating) small amounts of exhaust into the intake manifold through the EGR valve. Though the gases are hot, they actually have a cooling effect on combustion temperatures by diluting the air/fuel mixture slightly. Lowering the combustion temperature reduces the formation of NOX as well as the octane requirements of the engine.
If the EGR valve is not opening, either because the valve itself is defective or because its vacuum supply is blocked (loose, plugged or misrouted vacuum hose connections, or a defective vacuum control valve or solenoid), the cooling effect is lost. The result will be higher combustion temperatures under load and an increased chance of detonation.
Refer to a service manual for the configuration and hose routing of your engine's EGR system, and the recommended procedure for checking the operation of the EGR system.
3. Keep compression within reasonable limits. A static compression ratio of 9:1 is usually the recommended limit for most naturally aspirated street engines (though some newer engines with knock sensors can handle higher compression ratios).
Compression ratios over 10.5:1 may create a detonation problem even with 93 octane premium gasoline. So unless an engine is being built to run on racing fuel, keep the compression ratio within a reasonable range for pump gasoline. This, in turn, may require using lower compression pistons and/or cylinder heads with larger combustion chambers. Another option would be to use a copper head gasket shim with the stock head gasket to reduce compression.
Retarding the cam timing can also lower cylinder pressures to reduce detonation at low r.p.m., but doing so hurts low speed torque which is not recommended for street engines or cars with automatics.
For supercharged or turbocharged applications, a static compression ratio of 8:1 or less may be required depending on the amount of boost pressure.
Another point to keep in mind is that boring an engine's cylinders to accept oversized pistons also increases the static compression ratio. So too does milling the cylinder heads. If such modifications are necessary to compensate for cylinder wear, head warpage or damage, you may have to use a thicker head gasket if one is available for the application or a head gasket shim (a dead soft copper spacer shim) to offset the increase in compression.
4. Check for over-advanced ignition timing. Too much spark advance can cause cylinder pressures to rise too rapidly. If resetting the timing to stock specifications doesn't help, retarding the timing a couple of degrees and/or recalibrating the distributor advance curve may be necessary to keep detonation under control.
5. Check for a defective knock sensor. Many late model engines have a "knock sensor" on the engine that responds to the frequency vibrations characteristically produced by detonation (typically 6-8kHz). The knock sensor produces a voltage signal that signals the computer to momentarily retard ignition timing until the detonation stops.
If the "check engine" light is on, check the vehicle's onboard computer system using the prescribed procedure for a "trouble code" that would correspond to a bad knock sensor (code 42 or 43 for GM, code 25 for Ford, or code 17 for Chrysler).
A knock sensor can usually be tested by rapping a wrench on the manifold near the sensor (never hit the sensor itself!) and watching for the timing change while the engine is idling. If the timing fails to retard, the sensor may be defective -- or the problem may be within the electronic spark timing control circuitry of the computer itself. To determine the cause, you'll have to refer to the appropriate diagnostic chart in a service manual and follow the step-by-step test procedures to isolate the cause.
Sometimes a knock sensor will react to sounds other than those produced by detonation. A noisy mechanical fuel pump, a bad water pump or alternator bearing, or a loose rod bearing can all produce vibrations that can trick a knock sensor into retarding timing.
6. "Read" your spark plugs. The wrong heat range plug can cause detonation as well as preignition. If the insulators around the electrodes on your plugs appear yellowish or blistered, they may be too hot for the application. Try the next heat range colder spark plug. Copper core spark plugs generally have a broader heat range than ordinary plugs, which lessens the danger of detonation.
7. Check for engine overheating. A hot engine is more likely to suffer spark knock than one which runs at normal temperature. Overheating can be caused by a low coolant level, a slipping fan clutch, too small a fan, too hot a thermostat, a bad water pump, or even a missing fan shroud. Poor heat conduction in the head and water jackets can be caused by a buildup of lime deposits or steam pockets (which can result from trapped air pockets).
8. Check the operation of the heated air intake system. The thermostatically controlled air cleaner's job is to provide a carbureted engine with hot air when the engine is cold started. This aids fuel vaporization during engine warm-up. If the air control door sticks shut or is slow to open so that the carburetor continues to receive heated air after the engine is warm, the added heat may be enough to cause a detonation problem -- especially during hot weather. Check the operation of the air flow control door in the air cleaner to see that it opens as the engine warms up. No movement may mean the vacuum motor or thermostat is defective. Also, check the heat riser valve to make sure it's opening properly, as it, too, can affect the air intake system.
9. Check for a lean fuel mixture. Rich fuel mixtures resist detonation while lean ones do not. Air leaks in vacuum lines, intake manifold gaskets, carburetor gaskets or the induction plumbing downstream of a fuel injection throttle can all admit extra air into the engine and lean out the fuel mixture. Lean mixtures can also be caused by dirty fuel injectors, carburetor jets clogged with fuel deposits or dirt, a restricted fuel filter or a weak fuel pump.
If the fuel mixture becomes too lean, "lean misfire" may occur as the load on the engine increases. This can cause a hesitation, stumble and/or rough idle problem as well.
The air/fuel ratio can also be affected by changes in altitude. As you go up in elevation, the air becomes less dense.
A carburetor that's calibrated for high altitude driving will run too lean if driven at a lower elevation. Altitude changes are generally not a problem with engines that have electronic feedback carburetors or electronic fuel injection because the oxygen and barometric pressure sensors compensate for changes in air density and fuel ratios.
10. Remove carbon deposits. An accumulation of carbon deposits in the combustion chamber and on the top of the pistons can increase compression to the point where detonation becomes a problem. Carbon deposits are a common cause of detonation in high-mileage engines, and can be especially thick if the engine consumes oil because of worn valve guides and seals, worn or broken piston rings and/or cylinder wear. Infrequent driving and not changing the oil often enough can also accelerate the buildup of deposits.
In addition to increasing compression, carbon deposits also have an insulating effect that slows the normal transfer of heat away from the combustion chamber into the head. A thick layer of deposits can therefore raise combustion temperatures and contribute to "preignition" as well as detonation.
Carbon deposits can often be removed from an engine that's still in service by using a chemical "top cleaner." This type of product is poured into an idling engine through the carburetor or throttle body. The engine is then shut off so the solvent can soak into and loosen the deposits. When the engine is restarted the deposits are blown out of the combustion chamber.
If chemical cleaning fails to remove the deposits, it may be necessary to pull the cylinder head and scrape the deposits off with a wire brush or scraper (be careful not to scratch the face of the cylinder head or engine deck!).
11. Check the boost pressure. Controlling the amount of boost in a turbocharged engine is absolutely critical to prevent detonation. The turbo wastegate bleeds off boost pressure in response to rising intake manifold pressure. On most late-model engines, a computer-controlled solenoid helps regulate the operation of the wastegate. A malfunction with the manifold pressure sensor, the wastegate control solenoid, the wastegate itself or a leak in the vacuum connections between these components can allow the turbo to deliver too much boost, which destroys the head gasket as well as the engine in short order if not corrected.
Improved intercooling can help reduce detonation under boost. The intercooler's job is to lower the incoming air temperature after it exits the turbo compressor. Adding an intercooler to a turbo motor that isn't intercooled (or installing a larger or more efficient intercooler) can eliminate detonation worries while also allowing the engine to safely handle more boost.
12. Change your driving habits. Instead of lugging the engine, try downshifting to a lower gear and/or accelerating more gradually. Keep in mind, too, that the engine and drivetrain have to be matched to the application. If you're working your engine too hard, perhaps you need a transmission with a wider gear ratio or a higher final drive ratio in the differential.

PRE-IGNITION
Another condition that is sometimes confused with detonation is "preignition." This occurs when a point within the combustion chamber becomes so hot that it becomes a source of ignition and causes the fuel to ignite before the spark plug fires. This, in turn, may contribute to or cause a detonation problem.
Instead of the fuel igniting at the right instant to give the crankshaft a smooth kick in the right direction, the fuel ignites prematurely (early) causing a momentarily backlash as the piston tries to turn the crank in the wrong direction. This can be very damaging because of the stresses it creates. It can also localize heat to such an extent that it can partially melt or burn a hole through the top of a piston!
Preignition can also make itself known when a hot engine is shut off. The engine may continue to run even though the ignition has been turned off because the combustion chamber is hot enough for spontaneous ignition. The engine may continue to run-on or "diesel" and chug erratically for several minutes.
To prevent this from happening, some engines have a "fuel cutoff solenoid" on the carburetor to stop the flow of fuel to the engine once the ignition is turned off. Others use an "idle stop solenoid" that closes the throttle completely to shut of the engine's air supply. If either of these devices is misadjusted or inoperative, run-on can be a problem. Engines with electronic fuel injection don't have this problem because the injectors stop spraying fuel as soon as the ignition is turned off.

CAUSES OF PRE-IGNITION
Carbon deposits form a heat barrier and can be a contributing factor to preignition. Other causes include: An overheated spark plug (too hot a heat range for the application). Glowing carbon deposits on a hot exhaust valve (which may mean the valve is running too hot because of poor seating, a weak valve spring or insufficient valve lash).
A sharp edge in the combustion chamber or on top of a piston (rounding sharp edges with a grinder can eliminate this cause).
Sharp edges on valves that were reground improperly (not enough margin left on the edges).
A lean fuel mixture.
Low coolant level, slipping fan clutch, inoperative electric cooling fan or other cooling system problem that causes the engine to run hotter than normal.
Detonation vs power

some of the major factors in your engines potential power, is the volumetric efficiency (how efficiently you fill and empty the cylinders) and the octane of the fuel used, compression ratio and detonation limits,
With detonation, prevention the main factors are
Ignition timing
Quench
FUEL OCTANE
DCR
and cylinder heat level
you’ll be fairly safe if you stay under
8.5:1 dcr at 170f degrees
8.25 dcr at 180f degrees
7.8:1 dcr at 210f degrees
and keep the quench in the .036-.043 range
heres some differant calculators
http://www.kb-silvolite.com/calc.php?action=comp2 http://www.wallaceracing.com/dynamic-cr.php
http://www.smokemup.com/auto_math/compression_ratio.php http://not2fast.wryday.com/turbo/compression/cranking_pressure.shtml
average the results

the numbers are for 92 octane premium gas run at a 14.7:1 a/f ratio

BTW heres a VERY SIMILAR GRAPH

Image
[
Image
Image
IF YOU CAN,T SMOKE THE TIRES AT WILL,FROM A 60 MPH ROLLING START YOUR ENGINE NEEDS MORE WORK!!"!
IF YOU CAN , YOU NEED BETTER TIRES AND YOUR SUSPENSION NEEDS MORE WORK!!
grumpyvette

User avatar
Site Admin
Site Admin
 
Posts: 14105
Joined: September 14th, 2008, 1:40 pm
Location: florida

Re: detonation/pre-ignition

Postby grumpyvette » October 8th, 2011, 2:34 pm

these are all examples of damage done by either detonation,or excessive combustion heat, now the cause could be a lean fuel/air mix, low octane fuel with high compression or extreme heat from detonation and nitrous run a bit lean, or detonation resulting from the ignition timing being too far advanced
but look closely, the heat generally melts the thin part of a piston where the valve notch makes the piston thinner, so it tends to run a bit hotter, it doesn,t take long to melt the ring lands or melt thru a piston notch in the dome.
notice the frosted sugar like look of the melted aluminum, and the fact that the heat tends to find the thinner areas on the piston

both the rate of the ignition advance and where the ignition advance started at can be just as important as the total ignition advance.
theres several factors at work, but piston surface heat, quench and fuel octane are major factors in when detonation occurs
Most automotive engines use aluminium pistons that move in an iron cylinder. The average temperature of a piston crown in a gasoline engine during normal operation is typically about 300 °C (570 °F)
The self ignition temperature of gasoline mixed with air , in about a 14:1 ratio is about 495° F,, but it takes time for the incoming charge to absorb heat, theres much more time at lower rpms, at 3000rpm theres about 25 intake strokes per second, but at idle or 1000rpm theres three times longer for the fuel air mix in each compressing cylinder to absorb heat , the ignition advance is normally not needed past about 3200rpm because both increasing cylinder turbulence and rapid compression, plus increased heat levels speed up the combustion process.
it takes about 30-40 thousands of a second to have a cylinder burn during low rpm operation, leaving time for compressed gases to self ignite from absorbed heat and pressure building in the area near the spark plugs ignition point, at higher rpms theres far less time for the fuel to absorb heat and self ignite before the far more turbulent and rapid burn reaches the trapped gases, effectively making self ignition or detonation a non-issue.

Image
Image

Image
the dotted line shows pressure and heat during detonation
the solid line shows normal combustion pressure and heat
the inconsistent lines indicate missing or partial ignition
Image
hypothetically the ping or detonation your hearing could be the result of not the total timing but an ignition advance coming in to rapidly that over heats the cylinder to the point that even after the ignition advance is correct for the 3000rpm plus cylinder speed the cylinders already heated to the point it continues to detonate due to piston surface temps raised earlier in the pistons acceleration to 3000 plus rpm, so the cylinder temp just continues to increase further increasing the tendency to detonate, it doesn,t take a huge increase in cylinder heat to cause a cascade effect,pushing the conditions into detonation, if the compression and fuel octane levels are very close to reaching detonation to start with

related info


viewtopic.php?f=70&t=4683

http://zhome.com/ZCMnL/PICS/detonation/detonation.html

viewtopic.php?f=50&t=208&p=487&hilit=detonation+piston#p487

viewtopic.php?f=55&t=2718&p=12119&hilit=calculate+octane#p12119

viewtopic.php?f=54&t=10028&p=38941#p38941

viewtopic.php?f=70&t=4683

viewtopic.php?f=55&t=613&p=816#p816

viewtopic.php?f=52&t=4081&p=13147&hilit=quench#p13147
Image
the dotted line shows pressure and heat during detonation
the solid line shows normal combustion pressure and heat
the inconsistent lines indicate missing or partial ignition
Image
Image

Image

Image

Image

Image


Image

Image

Image

Image

Image

Image
Aluminum does have advantages, like light weight, and easy of machining compared to cast iron, example,cracks in valve seats on iron heads ",usually the result of overheating,"tend to result in coolant leaks that are not easily repaired, so you need a new cylinder head even if you had hundreds of dollars in port work done previously.
but on aluminum heads a bit of tig welding and machining for new valve seats repairs the heads rather easily

Image
Image
IF YOU CAN,T SMOKE THE TIRES AT WILL,FROM A 60 MPH ROLLING START YOUR ENGINE NEEDS MORE WORK!!"!
IF YOU CAN , YOU NEED BETTER TIRES AND YOUR SUSPENSION NEEDS MORE WORK!!
grumpyvette

User avatar
Site Admin
Site Admin
 
Posts: 14105
Joined: September 14th, 2008, 1:40 pm
Location: florida

Re: detonation/pre-ignition

Postby 87vette81big » August 8th, 2014, 10:03 pm

I found this old thread by You last night Grumpy.
Yes Preignition & Detonation are Enemy #1.
Take a Race Hero & Make Him Bankrupt broke in just 1-5 seconds.
Cost $10K - 100k to replace the blown up Engine.
Often nothing left like shown. Intake Manifold if your lucky.
87vette81big

User avatar
 
Posts: 3278
Joined: February 28th, 2012, 12:34 am
Location: Central Illinois


Return to Tools, Procedures, and Testing trouble shooting

Who is online

Users browsing this forum: No registered users and 4 guests

cron